USB Extension Cable

  • UTT-20G series
  • UTT-20G series
  • UTT-20G series
  • UTT-20G series
  • UTT-20G series
  • UTT-20G series
  • UTT-20G series
  • UTT-20G series
  • UTT-20G series
  • UTT-20G series
UTT-20G series UTT-20G series UTT-20G series UTT-20G series UTT-20G series UTT-20G series UTT-20G series UTT-20G series UTT-20G series UTT-20G series

UTT-20G series

  • Product ID:UTT-20G series
  • Interface:TYPE-C / TYPE-C
  • Application: USB extension cable
  • Shelf time:2020-02-10 11:07:19
  • Product description: USS USB 3.2 USB-C to USB-C male/male flat cable Gen2x2 20G.bps
  • INQUIRY

ADT-Link USB 3.2 type C to type C Flat Cable


Brand name: ADT-LINK

Product name:USB 3.2 type C flat Cable

Product model:UTT-20G series

Transferspeed:support of increased bandwidth up to 20G/bps

Wire length:3 ~ 300 cm, the length can be customized,

Current capacity: 3A (measured to support 3A within 50cm, 1.5A within 1 meter)

Product application: GPS navigator, ROCK Pi 4 Raspberry Pi microcontroller development board, built-in USB device to extend the use of adapter.

Procurement Tips: Be sure to buy 1~2 samples first and then purchase in bulk after testing and verifying that they are correct.

Purchase restriction: This product is designed to connect to built-in USB devices. It is not suitable for general external use. It is limited to the product engineer to specify the purchase. Individual buyers should not place an order for purchase. This product has a fragile structure and is not suitable for civilian use. It is not easy to use for general purposes and does not support returns and exchanges. Please consider carefully before placing an order.

ADT USB series Part-Number Description:

S=USB-A ; C=USB-C ; W=USB-B ; F=USB-E



USB TYPE-C male to TYPE-C cable,UTT-20G series

Product-Name

Part-Number

Transfer-Speed

USB3.2 Flat mount USB-C male to Flat mount USB-C male with e-mark IC Cable UT6A-UT6B 20G or 10G+displayport
USB3.2 Flat mount USB-C male to Flat mount USB-C male without e-mark IC Cable UT6A-UT6B-NC 20G or 10G+displayport
USB3.2 Flat mount USB-C male to Flat mount USB-C female without e-mark IC Cable
UT6A-UT7B-NC
20G or 10G+displayport
USB3.2 Flat mount USB-C male to right angle USB-C female without e-mark IC Cable UT6A-UT8T-NC 20G or 10G+displayport
USB3.2 Flat mount USB-C male to right angle USB-C female without e-mark IC Cable with PCI bracket UT6A-UT8T-NC-BK 20G or 10G+displayport
USB3.2 Right angle USB-C male to Flat mount USB-C male with e-mark IC Cable UT9A-UT6B 20G or 10G+displayport
USB3.2 Right angle USB-C male to Flat mount USB-C male without e-mark IC Cable
UT9A-UT6B-NC
20G or 10G+displayport
USB3.2 Right angle USB-C male to Flat mount USB-C female without e-mark IC Cable
UT9A-UT7B-NC
20G or 10G+displayport
USB3.2 Right angle USB-C male to right angle USB-C female without e-mark IC Cable
UT9A-UT8T-NC
20G or 10G+displayport
USB3.2 Right angle USB-C male to right angle USB-C female without e-mark IC Cable with PCI bracket
UT9A-UT8T-NC-BK
20G or 10G+displayport



T6A/T6B straight type-C male connector
T7B straight type-C female connector
T8T angled type-C female connector with 2 positioning holes
T9A angled type-C male connector
Model with -NC means no e-mark chip; Model with -BK means PCI baffle.
Remark 1: Speed bandwidth: gen2 speed is supported within 50cm, and gen1 speed is supported within 3 meters.

Cable length Description:

The length of the wire refers to the part of the visible wire. It does not include the PCB and the connector. For the wire length, please refer to the 4cm black arrow in the figure below.

Q&A:

Is there any EMI shielding for Cable?

The extender utilizes the latest materials for EMI shielding with five sole flat cables design. This technique allows each cable to be fully covered by electromagnetic interference shielding with conducting polymer to guard against incoming or outgoing emissions of electromagnetic frequencies, minimize disturbance and degradation on performance, and reduce the weight of the extender.

Can wires and PCB connectors be split?

No, in order to purify the signal transmission and avoid the accident of wire falling off, our wire and PCB connectors is soldering and protected by the heat shrinkable tube sleeve, so the product can not be separated.

Cable thickness? Can it be bent?

The thickness of the wire is 1.4mm, and it can be bent and folded without affecting the use.

What is the difference between product model T6A with chip and without chip?

T6A with chip refers to the PCB with RT1710 e-mark chip from RichTek, which supports high current 3A, up to 5A. Compatibility, scalability, and security are relatively good. Support Alternate Mode, Vendor Defined Message (USB PD)
The T6A-NC version without a chip is only suitable for general use and does not support high current. The USB data transmission function can still be used normally.

Photo:

Download:

To open 3D PDF files. Please use Adobe Reader DC software.

FTP: Los Angeles

3D STEP & PDF files download http://www.adt.link/Uploads/download/ADT_UTT3_3D.zip

FTP: Hong Kong

3D STEP & PDF files download http://www.adtlink.cn/Uploads/download/ADT_UTT3_3D.zip

WebShop:

http://www.adt.link/product/UTT-20G-Shop.html


Keywords:

Aerial FPV PTZ USB 2.0 3.0 3.1 flexible flat ribbon cable FFC cable FPV displayport flat Cable Standard Male to female Straight

Converter Cable Angle   thin flat highly-routable foldable axial elbow A type 10G/bps 5G/bps

3 / 5 /10 /15 /20 /30 /50 / 100 / 150 / 200 cm For PC AV HDTV LCD FPV FFC 3D  Multicopter

2K 4K 50/60Hz for HDTV AV Aerial Photography 90 Degree ConnectorDrone Gopro DSLR gimbal kit

Categories

Latest News

Contact Us

Contact: adt-sales@adt.link

Phone: 021-65312041

Tel: 021-65312041

Add: Shanghai, China